2025 RAM 1500 REV Alignment in Albuquerque, NM

Expect about 60 minutes for a complete four-wheel alignment on a 2025 Ram 1500 REV.

That time covers lift-up, full suspension inspection, computerized measurement, and adjustments to factory specs for this rear-wheel-drive electric pickup. Local road conditions in Albuquerque — from potholes to frost heaves — can add extra time if we find worn components that need repair.

• Computerized four-wheel measurement and adjustment
• Suspension and tie-rod inspection before alignment
• Road test following adjustments

Get an alignment every 2–3 years or about every 30,000 miles, and after suspension work or major pothole impact.

Albuquerque roads, occasional construction, and canyon driving can accelerate wear. If you notice steering pull, off-center steering, or irregular tire wear sooner, bring your 2025 Ram 1500 REV in for inspection. The dealership provides a clear before-and-after printout so you can track changes over time.

• After new tires or suspension repairs
• After hitting a large pothole or curb
• Routine check every 2–3 years or 30,000 miles

Common signs include uneven tire wear, the vehicle pulling to one side, an off-center steering wheel, or vibration at speed.

These symptoms on a 2025 Ram 1500 REV often indicate toe, camber, or caster are out of spec or that suspension components are worn. If you see feathered or scalloped tread, or the truck drifts on straight roads in Albuquerque, schedule an inspection to diagnose the root cause.

• Uneven tread wear or feathering on tires
• Truck pulls left or right during normal driving
• Steering wheel not centered when driving straight

A four-wheel alignment includes caster, camber, and toe adjustments to factory specifications plus a printed before-and-after alignment report.

For the 2025 Ram 1500 REV we perform a full suspension inspection, measure each corner with OEM-calibrated equipment, adjust to factory tolerances, and follow with a road test. Technicians verify tire pressure and steering component condition so the alignment holds under real driving conditions.

• Suspension and tie-rod inspection before adjustments
• Caster, camber, and toe set to factory spec with before/after printout
• Final road test to confirm handling and tracking

If tie rods, ball joints, or struts are worn, repairs are required before a successful alignment will hold.

Technicians at Larry H. Miller Chrysler Jeep Dodge Ram Albuquerque inspect suspension components first; if they find play or damage we’ll explain needed repairs and show affected parts. Worn steering or suspension pieces are common after curb strikes or repeated pothole impacts on local roads, and replacing them prevents premature re-alignment and tire wear.

• Inspection identifies worn tie rods, ball joints, or bushings
• We repair or replace parts before resetting alignment where necessary
• Follow-up alignment verifies repairs corrected the issue

Not always — if the truck tracks straight and tire wear is even, an alignment can usually wait until a symptom, tire change, or suspension service occurs.

For the 2025 Ram 1500 REV, alignment is recommended after new tires, suspension repairs, or any steering feel change. In Albuquerque, road hazards and construction make periodic checks sensible even without obvious symptoms; a printed before/after report provides certainty when you do choose to align.

• Consider alignment after new tires or suspension work
• Schedule an inspection if you notice pull or uneven wear
• Use a before/after report to confirm steering geometry

Our service center in Albuquerque supports drivers across nearby neighborhoods and routes with alignment work tailored to the 2025 Ram 1500 REV. Local driving includes highway miles, canyon roads, and areas with periodic road construction and potholes; these conditions can change suspension geometry over time. Technicians use calibrated, OEM-style alignment equipment to measure and correct caster, camber, and toe. We document results with a printed before-and-after alignment report and conduct a road test so you leave with verified tracking and handling.

Bring your 2025 Ram 1500 REV to Larry H. Miller Chrysler Jeep Dodge Ram Albuquerque for an alignment designed for the vehicle’s electric drivetrain and rear-wheel setup. For convenience, schedule service online or check current offers on our service specials.

The 2025 Ram 1500 REV requires factory caster, camber, and toe tolerances checked and adjusted independently at the front and rear to ensure even tire wear and correct steering geometry. Technicians measure each corner with computerized alignment racks and reference OEM tolerances for the rear-wheel-drive layout. Common issues we see on this model include toe change after curb impacts and camber shifts from bent control arms. Bring your 2025 Ram 1500 REV to Larry H. Miller Chrysler Jeep Dodge Ram Albuquerque in Albuquerque for a factory-spec alignment — schedule service.

The service begins with a visual and hands-on suspension and tie-rod inspection, followed by tire pressure and condition checks. Next, we use calibrated alignment equipment to measure caster, camber, and toe at each wheel and adjust all settings to factory specifications. A printed before-and-after alignment report is provided, and a road test confirms steering feel and tracking. If additional repairs are required, the technician will explain them and outline recommended next steps.

If you’d like to schedule service, or learn about current offers on our service specials, contact the service desk at Larry H. Miller Chrysler Jeep Dodge Ram Albuquerque.