2025 Ram 1500 Alignment

Get a four-wheel alignment every 2–3 years or about every 30,000 miles, and anytime after suspension work or a major pothole impact.

That guidance helps preserve even tire wear and factory steering geometry for the 2025 Ram 1500 in Albuquerque, where road construction and seasonal freeze-thaw can accelerate misalignment. If you replace tires, install a lift or leveling kit, or have a steering component replaced, schedule an alignment immediately.

• Typical interval: every 2–3 years or ~30,000 miles
• Immediately after suspension or steering repairs
• After hitting a large pothole or curb

Four common signs are uneven tire wear, the vehicle pulling to one side, an off-center steering wheel, or vibration at speed.

On a 2025 Ram 1500, these symptoms usually point to toe or camber deviation that should be measured with OEM alignment gear. In Albuquerque, check sooner if you frequently drive on construction-affected roads or hit potholes.

• Uneven wear across the tire tread
• Truck pulls left or right while driving straight
• Steering wheel not centered when driving straight

A four-wheel alignment includes caster, camber and toe adjustments to factory specifications with before-and-after printouts, plus a suspension inspection and road test.

For the 2025 Ram 1500 our technicians verify tire pressures, inspect tie rods, ball joints, and bushings, measure front and rear geometry with OEM-calibrated equipment, and perform a road test to confirm handling. You receive documented readings showing the correction made.

• Suspension and tie-rod inspection before adjustments
• Caster, camber, and toe set to factory specs
• Before/after alignment printout and final road test

If worn components like tie rods, ball joints, control-arm bushings, or bent parts are present, alignment alone will not hold and parts replacement is required.

Technicians inspecting your 2025 Ram 1500 will look for play, torn boots, and visible damage before attempting adjustments. In Albuquerque, road hazards can accelerate wear; we report any parts that need replacement so the alignment will stay within spec.

• Shop inspects tie rods, ball joints, and bushings first
• Replacement parts are required if there is excessive play or damage
• Alignment is completed after suspension issues are resolved

Not always — if the 2025 Ram 1500 tracks straight and shows no uneven wear, an alignment can usually wait until symptoms or component work appear.

However, an alignment is recommended after new tire installation, suspension repairs, or after hitting a significant pothole in Albuquerque. A baseline alignment and printout give you documentation that geometry met factory specs at the time of service.

• Consider alignment after tire replacement
• Do it after suspension or steering repairs
• Use a baseline alignment to document factory-spec geometry

Most four-wheel alignments are completed in about 60 minutes from inspection to road test.

For a 2025 Ram 1500 the total time depends on whether suspension repairs are needed; if we find worn components we will contact you with an estimate and timeline. Plan for additional time if parts replacement or ordering is required.

• Typical service bay time: ~60 minutes
• Longer if parts or repairs are required after inspection
• Call ahead or schedule service to reserve a slot

Our four-wheel alignment for the 2025 Ram 1500 follows a step-by-step process that begins with a full suspension inspection. Technicians check tie rods, ball joints, control-arm bushings, steering linkages, and tire condition. We confirm and set recommended tire pressures, then mount OEM-calibrated alignment heads to measure caster, camber, and toe for front and rear axles.

Adjustments are made to bring each axis to factory specifications, and we print before-and-after alignment readings for your records. A road test verifies steering return and handling. If worn or damaged components are found, we recommend repairs before final alignment so the settings will hold. For available service discounts see service specials.

Schedule a factory-spec alignment for your 2025 Ram 1500 through our schedule service page.

Larry H. Miller Chrysler Jeep Dodge Ram Albuquerque serves drivers across Albuquerque and nearby neighborhoods, providing alignment work tailored to local driving conditions. With frequent road construction, occasional frost heaves, and potholes that can affect geometry, drivers bring the 2025 Ram 1500 to our service center for timely inspections and adjustments.

Technicians use OEM-calibrated alignment equipment and documented procedures to return caster, camber, and toe to factory targets. We provide clear before/after reports and advise on necessary suspension repairs. For appointment availability, schedule service online or visit our service department page for directions and hours.

Factory alignment for the 2025 Ram 1500 focuses on three primary angles: caster, camber, and toe. Technicians adjust the front axle caster and camber where serviceable, and set front and rear toe to the manufacturer’s specifications. Using OEM-aligned fixtures and digital measurement heads ensures readings match factory targets for safe handling and even tire wear.

Common issues on pickup trucks like the 2025 Ram 1500 include toe drift from worn tie rods or camber changes from bent control arms after impacts. Bring your 2025 Ram 1500 to Larry H. Miller Chrysler Jeep Dodge Ram Albuquerque in Albuquerque for a factory-spec alignment — schedule service.