2018 RAM 3500 Alignment in Albuquerque, NM

Get an alignment every 2–3 years or about every 30,000 miles, and always after suspension repairs or a major pothole impact.

For a 2018 Ram 3500 used in Albuquerque, routine driving on city streets and occasional highway towing can gradually alter toe and camber. A proactive schedule helps preserve tire life and maintain steering precision, especially when towing heavy loads near the truck’s 17,150 lb capacity.

• Every 2–3 years or ~30,000 miles as routine guidance
• After replacing tires, shocks, or steering components
• After hitting a large pothole or curb while towing

Four common signs are uneven tire wear, the vehicle pulling to one side, an off-center steering wheel, and vibration at speed.

On a 2018 Ram 3500, uneven wear can appear faster when carrying heavy loads or towing. Pulling or a crooked steering wheel often indicates toe or camber deviation; vibrations can signal wheel misalignment or an imbalanced tire combined with the truck’s heavier suspension setup.

• Inspect tires for inner or outer edge wear
• Noticeable pull left or right while driving straight
• Steering wheel not centered when driving straight

A four-wheel alignment includes three primary adjustments—caster, camber and toe—plus a suspension inspection and before/after printouts showing factory-spec settings.

Technicians measure front and rear angles, correct toe and camber to factory specifications, and check steering and suspension components on the 2018 Ram 3500. The process confirms alignment values hold under load and after a road test, which is important for trucks that tow or carry payloads near their rated capacity.

• Measure caster, camber and toe to OEM specs
• Inspect tie rods, ball joints, and suspension for wear
• Provide printed before-and-after alignment readings

If you have loose steering play, clunking suspension noise, or visible worn components (tie rods, ball joints, control arms), alignment alone will not fix the issue.

When suspension components are worn, they allow geometry to shift after adjustments; the tech will inspect the 2018 Ram 3500’s steering and suspension before performing an alignment. If parts need replacement, the dealership documents required repairs, then completes a factory-spec alignment afterward so the settings hold under load.

• Loose steering or excessive play indicates component wear
• Clunks, squeaks, or visible torn boots require repair first
• Dealer inspects components and recommends needed parts before alignment

If the 2018 Ram 3500 tracks straight and shows no symptoms, an alignment is not always required at every service; it’s worth doing after new tires, suspension work, or any steering changes.

A straight-tracking truck can still have subtle deviations that accelerate tire wear when used for heavy towing. For owners in Albuquerque who tow or operate on variable road surfaces, confirm alignment when buying used, after installing new tires, or after suspension or steering repairs.

• Not mandatory if no symptoms and no component changes
• Recommended after new tires, shocks, or steering repairs
• Helpful to check before a long towing trip or heavy seasonal use

Schedule service online using the dealer's service scheduler or call the service department to book an alignment appointment.

To arrange a four-wheel alignment or suspension inspection for your 2018 Ram 3500, use the secure online form on the dealership site or mention alignment checks when you call. The service center documents vehicle details and any towing or payload use so technicians apply factory-spec settings appropriate for heavy-duty trucks.

• Use the online scheduler to pick date and time: schedule service
• Ask for a suspension inspection and before/after printout
• Check service specials before booking: service specials

The 2018 Ram 3500 requires alignment work suited to heavy-duty trucks: technicians verify angles with the truck unloaded and under simulated load when needed. In Albuquerque, local driving includes city streets and regional highways where potholes and road repairs can alter alignment. The service center documents towing history and recent repairs before adjusting settings. For scheduling, use the online appointment tool or visit the dealership service desk to discuss towing or payload details so alignment decisions match real use patterns.

Bring vehicle service records if possible; note tire condition and recent steering or suspension work to speed diagnosis. For appointments, schedule service online.

Service for a 2018 Ram 3500 four-wheel alignment follows clear steps: technicians begin with a visual suspension and steering inspection, including tie rods, ball joints, and bushings. They check tire pressures and wear patterns, then mount OEM-grade alignment targets and measure caster, camber and toe for front and rear axles. Adjustments are made to factory specifications and a road test confirms the truck tracks straight under normal loads.

Customers receive printed before-and-after alignment readings and a summary of any recommended repairs. To book an alignment, schedule service online or view current offers on service specials.

Factory alignment work on the 2018 Ram 3500 focuses on caster, camber and toe values set to OEM tolerances for both front and rear where adjustable. Technicians use manufacturer-grade alignment racks and calibration to ensure repeatable results; adjusting toe and camber on the front axle is common after suspension work, while rear adjustments depend on axle type and mounting. Common issue callouts for this truck include toe drift after heavy towing and accelerated inner tire wear if not corrected.

Bring your 2018 Ram 3500 to Larry H. Miller Chrysler Jeep Dodge Ram Albuquerque for a factory-spec alignment — schedule service.